Pyronix Paragon Super Especificaciones descargar pdf (Pagina 8)

8 21

RDOC 279 issue 1

7 CONTROLS AND FUNCTIONS

Volume Control

This is only accessible when the front cover has been removed and will only affect

the volume of any extension speakers. The volume control is overridden when the

panel is in an alarm state, and also if the the panel has been set by either the Master

User or Limited User four digit codes. This feature will allow a reduced volume tone on

part-set modes.

Chime

Chime function applies to day mode only and if selected will cause the panel to

generate a three-note sound when an entry/exit zone is triggered. This feature is to

inform the occupants of the building that some one has entered.

Event Log

The Paragon Super control panel incorporates a memory log of the last 18 alarm

events and is accessible to both Users and the Engineer. It will record Fire, Intruder,

Personal Attack and Tamper alarms and also show if any of the 6 alarm zones have

been triggered or omitted.The Engineer can set the clearing of the log for either

Engineer-only or Master User and Engineer.

Auto Rearm

After an alarm the panel will automatically reset itself when the bell timer has expired.

Any zones which still remain triggered at that time will be omitted automatically.

Walk test

The walk test function allows each of the fullset / partset modes to be checked in

order to verify that all the intruder detectors on the alarm system are functioning

correctly. When undergoing a walk test the Engineer or Master User can choose

which of the set-modes he wishes to test. Any zones used in that set-mode will

cause a chime at the RKP or extension speaker l if they are triggered.

8 INSTALLATION AND WIRING

Before beginning any installation work read through this section carefully. Plan out the

various areas and degrees of protection required from each zone. It is important to

decide which type each zone should be if partsets are to be used. Work out the cable

routes avoiding mains cabling and consider the chosen position for the control panel

and its mains supply.

1 2 TECHNICAL SPECIFICATION

12.1 POWER SUPPLY/RKP

Power input

230V version : 230V ac +/- 10%, 50Hz/60Hz

220V version : 220V ac +/- 10%, 50Hz/60Hz

110V version : 110V ac +/- 10%, 50Hz/60Hz

Power input fuse

240, 230, 220V versions : 250 mA quick blow.

110V version : 500 mA quick blow.

Low voltage output : 13.2 Vdc fused, 0.5A Continuos 1.0A peak(20min)

Low voltage output fuse : 1 Amp quick blow.

Battery charge voltage : 13.7 Vdc

Rechargeable battery capacity : 12V sealed lead acid, 1.2 to 6 AH.

12.2 CONTROL PCB

Current consumption (day mode) : 45mA (quiescent)

: 55mA (with keypad LEDs)

(set mode) : 45mA

(test) : 120mA (all LEDs on)

(alarm ) : 210mA

Auxiliary DC output supply : Regulated 13.2 Vdc for use with PIR, microwave,

and shock sensors.

Extension Speaker load : 8 to 32 Ohms

Alarm Bell current : 0.5 Amps (maximum)

Alarm Bell timer : 2 to 20 minutes (software programmable)

Strobe current : 0.5 Amps (maximum)

Zone type : Normally closed loops which activate when opened or

connected to 0 volts from dc power supply.

Zone loop current : 1.2 to 1.5mA

Zone activation resistance : 2k Ohms (minimum)

Zone loop activation time : 0.35 seconds

Entry / Exit timer : 2 to 255 seconds (software programmable)

12.3 MECHANICAL

Dimensions : 223 x 205 x 78 mm (8.78 x 8.07 x 3.07 inches)

Case Material : 3mm thick Polycarbonate with screw fixing front cover

Colour : White

Weight (excluding battery) : 1.48 kg

12.4 ENVIRONMENTAL

Operating temperature : 0 to +40 deg C (+32to +104 deg F)

Storage temperature : -20 to +60 deg C (-4 to +140 deg F)

12.5 CLEANING

DO NOT use strong detergents to clean this panel. To remove any dirt or grime, wipe with a clean damp cloth ONLY.

1 2 3 4 5 6 7 8 9 10 11 12 13 14

Comentarios a estos manuales

Sin comentarios

Pyronix Paragon Super Especificaciones Pagina 8

Comentarios a estos manuales